So I am stumped. I have never had a problem changing brakes, ever. My buddy comes over today with his 06 nissan frontier 4wd. Bought some new pads for all four corners and new cross drilled and slotted rotors for all around as well. The brakes I pulled off were pretty much new, both rotors and pads, with hardly ANY wear on them. Pulled the front rotors and pads, replace rotors. The pistons on the calipers needed to be pushed back a tad to let the new pads slide over the new rotors. I had to push them back maybe 2-3 millimeters at most. I took the brake fluid cap off, for when I push the pistons in, the fluid will rise. I bought one of those brake caliper piston pusher things years ago to do all of my brakes. Get the front all buttoned up and do the rears, same thing, fairly easy. Check the fluid level, all is good. Put the cap back on. Pump the brakes a dozen time to stiffen the pedal, and it's soft. Do an oil change, pull the truck out of the garage, and the brakes are soft still.
Drive down the road, they stop, but again, very soft. I'm stumped. So I decided to bleed all four corners, nothing. Then I bled the master cylinder, still nothing. I'm clueless.
I did not feel what his brakes felt like before the change, as I wish I did. He said he wasn't sure if they were soft before or not.
The pads and rotors were the same thickness as the old ones. Everything was the same size, width and diameter.
So, anyone have any clues?
__________________ "In the business world, the rearview mirror is always clearer than the windshield."
So I am stumped. I have never had a problem changing brakes, ever. My buddy comes over today with his 06 nissan frontier 4wd. Bought some new pads for all four corners and new cross drilled and slotted rotors for all around as well. The brakes I pulled off were pretty much new, both rotors and pads, with hardly ANY wear on them. Pulled the front rotors and pads, replace rotors. The pistons on the calipers needed to be pushed back a tad to let the new pads slide over the new rotors. I had to push them back maybe 2-3 millimeters at most. I took the brake fluid cap off, for when I push the pistons in, the fluid will rise. I bought one of those brake caliper piston pusher things years ago to do all of my brakes. Get the front all buttoned up and do the rears, same thing, fairly easy. Check the fluid level, all is good. Put the cap back on. Pump the brakes a dozen time to stiffen the pedal, and it's soft. Do an oil change, pull the truck out of the garage, and the brakes are soft still.
Drive down the road, they stop, but again, very soft. I'm stumped. So I decided to bleed all four corners, nothing. Then I bled the master cylinder, still nothing. I'm clueless.
I did not feel what his brakes felt like before the change, as I wish I did. He said he wasn't sure if they were soft before or not.
The pads and rotors were the same thickness as the old ones. Everything was the same size, width and diameter.
So, anyone have any clues?
My guess is that he had a soft pedal before you worked on it.
Sometimes it is hard to bleed ABS system I would try bleeding again sounds like air in the system.
He's going to try to find a brake place open tomorrow to diagnose it for free. I took it to a shop I do business with down the road, but they couldn't get to it before they closed today....
__________________ "In the business world, the rearview mirror is always clearer than the windshield."
He's going to try to find a brake place open tomorrow to diagnose it for free. I took it to a shop I do business with down the road, but they couldn't get to bet t it before they closed today....
may be try cross bleeding the brakes also check and make sure brake fluid is not mixed with oil/or power dteering fluid just had buddys kid put in power steering fluid in master cylinder
So, he wanted to change the brake fluid out anyways. Would a shop pressure bleeding the system fix the air issue, if there is even air in the system? And what would something like that, on average (ballpark) run?
__________________ "In the business world, the rearview mirror is always clearer than the windshield."
It could just be a case of the new brakes not "seating in" It can take several miles... I bought a new motorcycle and I thought the brakes weren't working. It was just a matter of them seating in.
You should also avoid sudden stops. Treat them gentle for the first couple hundred miles!!
Modern braking systemsneed to be bled differently than many of us were taught. You don't always go right rear, left rear, right front, left front. The systems are now set up so that one left and one right brake (diagonal usually) go on each chamber. GM A-bodies from 82-96 for example, are like this. And that's why so many of those cars have a) soft pedals, b) need master cylinder replacements, and c) end up in the junkyard.
And that's why so many of those cars have a) soft pedals, b) need master cylinder replacements, and c) end up in the junkyard.
__________________ "I am not aware of any misconceptions. I think everybody knows I rock harder than any human being ever, have created the top 100 guitar licks of all time, constantly kill many innocent animals and own more guns that the Cuban Army. What's to misconceive?" - Ted Nugent, on being asked what he thought people's biggest misconception about him is.
1988 Century, bought for $275 at 217K, drove to 231K, sold for $550, subsequent owner traded it a year later for a 1991 Civic which threw its timing belt within a month.
1989 Century, bought for $250 at 229K, drove to 238K, impounded by city because I had a badly signed title and couldn't register it.
1987 Celebrity, bought for $132.50, this one was junk with no brakes when I got it but I drove it with no brakes from Indiana to Texas and it served as a good storage unit while I drove cabs.
1989 Celebrity, bought for $400, drove it for about a year and the dealer never gave me a title, I had to scrap it because I couldn't get tags.
1989 Ciera, bought for $172.50, oil pump failed, scrapped it
1995 Century, parents bought new, ran it to 224K, gave it to me, I hit 270K and traded it for a minivan.
1989 Celebrity, bought for $300, I blew the head gasket and scrapped it when I bought an Intrepid to replace it.
My neighbor (a few years older than me) got one of these for his first car. We dogged the heck out of that thing. It finally died on us when we jumped a set of railroad tracks and came down on the nose/front end. Fun times....
__________________ "I am not aware of any misconceptions. I think everybody knows I rock harder than any human being ever, have created the top 100 guitar licks of all time, constantly kill many innocent animals and own more guns that the Cuban Army. What's to misconceive?" - Ted Nugent, on being asked what he thought people's biggest misconception about him is.
I always thought you should open the bleeder valve on the caliper instead of opening the filler cap. Then you aren't pushing the crappy fluid back into the master cylinder
Linear Mode
